How to Install Door Pulls: Here are some of the mistakes I have made when installing a pull. Drilling pilot holes in the wrong place, making them too big or small, can quickly lead to an annoying problem for homeowners who want their homes’ locks fixed without too much hassle! Fortunately, with these simple steps, you’ll be able to avoid all those inconveniences I and others before me experienced by learning how important it is that pilots align correctly and stay away from any sharp edges near where the paint will go later on.
The devil is in the details, and there’s no more minor detail than hardware for your cabinets, drawers, or closets. I’ve installed some of it above, as you can see (clockwise from top left), my kitchen cabinet handles with Medusa heads on them; black pulls to match the rest of my dark wood furniture.
I hope this helps!
Procedure
Here are some of the easy steps you need to follow to install the door pull in the right way.
Step 1
When it comes time to buy your closet hardware, make sure you find something that matches the rest of your decor and is functional as well. For this project, I needed a small knob within 2″ wide wood panels but large enough so my hand could grip onto it easily when opening or closing doors to avoid having too much difficulty doing these tasks myself!
You may also like Keypad Door Lock: The Best Smart Door Locks
Step 2
Where to put your hardware is a question you’ll want to answer before installing anything. For closets, the best place for pulls or knobs will depend on what height doorknob they’re paired with–and this depends mainly from were in relation toward one another, that space within which it’s being placed (closet vs. bedroom). If there are no cabinets present at all levels along these edges, then consider making fixtures high enough so as avoid looking “low.”
Step 3
Center or align the pull and mark its location with a pencil, using an accurate measuring tool if necessary. If you’re installing more than one hole in this part of your project, make sure to use templates for precision—measuring twice is always better! Then drill only where needed so that everything fits correctly without having too much excess material (this will lead us into our next tip).
Step 4
There are a few things you should consider when drilling your hole. First, make sure that the size of it is close enough so as not too loose or remove any threaded pieces from inside and outside surfaces with each pass through; secondarily – depending on what type of hardware rod (if there’s more than one) choose which will fit best by measuring its length before going forward because once they’re installed these accessories can’t move much distance apart without becoming disengaged at their attachment points- lastly always wear gloves while working around metal parts!
Step 5
The key to making straight holes is using a cordless drill. It’s small and lightweight, so you can guide it with more control instead of being stuck using an entire significant tool that may move around on your desk or floorboard while drilling!
You may also like WYZE Smart Lock Review: A Bluetooth Enabled Door Lock
Step 6
The hardest part about installing this handle was finding the proper wrench. It took some trial and error, but I finally found one that fits perfectly into its slot on top of my door (no denting!). Remember: Be very careful not to put too much pressure when turning it clockwise as you may bend things away from what they’re supposed to look like! You can use cloth or rubber bands for protection against scratches while doing.
It is essential to have patience while installing this part of the door. It took 5 minutes or longer for me to rotate that screw, but it depends on how thick your wall is and if there are long rods in front too!
Step 7
The washer will now be attached to the rod, and you can tighten it with a wrench.
Extra tip
The best way to install pulls is by using a drill bit that has been designed with the specific purpose of making precise holes. The sharp point on these drills prevents them from sliding or moving when you are trying to penetrate deep into your project’s materials, which means there’ll be no issues whatsoever!
How are Edge pulls installed?
Edge pulls are a unique way to add functionality and style. Unlike traditional cabinet hardware, which drills through the surface of your cabinets with an attachment point on its front side for screws or nails used in fastening things like door pull handles – these edge screw installations require no drilling at all! Instead, they use wood threads attached by predrilled holes that allow them to drop right into place when you’re done using it and then take away just as quickly once the business has been conducted.
You may also like Nest Doorbell: How to Keep Tabs On Your Home with Google
How big should edge pulls be?
Consider the size of your cabinet when choosing pulls. We recommend at least a 3-3/4 inch center to hole distance (the equivalent on most cabinets) and 5″ for larger ones, which will grip comfortably without being too tight or loose depending on the space you have available in between them.
Would you like to read more about How to Install Door Pulls or DIY-related articles? If so, we invite you to take a look at our other tech topics before you leave!
